TH03 gameplay! 📝 It's been over two years. People have been investing some decent money with the intention of eventually getting netplay, so let's cover some more foundations around player movement… and quickly notice that there's almost no overlap between gameplay RE and netplay preparations? That makes for a fitting opportunity to think about what TH03 netplay would look like:
You'd want UDP rather than TCP for both its low latency and its NAT hole-punching ability
However, raw UDP does not guarantee that the packets arrive in order, or that they even arrive at all
WebRTC implements these reliability guarantees on top of UDP in a modern package, providing the best of both worlds
I'm not too deep into networking to argue here, and it clearly works for Ju.N.Owen. If we do explore other options, it would mainly be because I can't easily get something as modern as WebRTC to natively run on Windows 9x or DOS, if we decide to go for that route.
Matchmaking: I like Ju.N.Owen's initial way of copy-pasting signaling codes into chat clients to establish a peer-to-peer connection without a dedicated matchmaking server. progre eventually implemented rooms on the AWS cloud, but signaling codes are still used for spectating and the Pure P2P mode. We'll probably copy the same evolution, with a slight preference for Pure P2P – if only because you would have to check a GDPR consent box before I can put the combination of your room name and IP address into a database. Server costs shouldn't be an issue at the scale I expect this to have.
Rollback: In emulators, rollback netcode can be and has been implemented by keeping savestates of the last few frames together with the local player's inputs and then replaying the emulation with updated inputs of the remote player if a prediction turned out to be incorrect. This technique is a great fit for TH03 for two reasons:
All game state is contained within a relatively small bit of memory. The only heap allocations done in MAIN.EXE are the 📝 .MRS images for gauge attack portraits and bomb backgrounds, and the enemy scripts and formations, both of which remain constant throughout a round. All other state is statically allocated, which can reduce per-frame snapshots from the naive 640 KiB of conventional DOS memory to just the 37 KiB of MAIN.EXE's data segment. And that's the upper bound – this number is only going to go down as we move towards 100% PI, figure out how TH03 uses all its static data, and get to consolidate all mutated data into an even smaller block of memory.
For input prediction, we could even let the game's existing AI play the remote player until the actual inputs come in, guaranteeing perfect play until the remote inputs prove otherwise. Then again… probably only while the remote player is not moving, because the chance for a human to replicate the AI's infamous erratic dodging is fairly low.
The only issue with rollback in specifically a PC-98 emulator is its implications for performance. Rendering is way more computationally expensive on PC-98 than it is on consoles with hardware sprites, involving lots of memory writes to the disjointed 4 bitplane segments that make up the 128 KB framebuffer, and equally as many reads and bitshift operations on sprite data. TH03 lessens the impact somewhat thanks to most of its rendering being EGC-accelerated and thus running inside the emulator as optimized native code, but we'd still be emulating all the x86 code surrounding the EGC accesses – from the emulator's point of view, it looks no different than game logic. Let's take my aging i5 system for example:
With the Screen → No wait option, Neko Project 21/W can emulate TH03 gameplay at 260 FPS, or 4.6× its regular speed.
This leaves room for each frame to contain 3.6 frames of rollback in addition to the frame that's supposed to be displayed,
which results in a maximum safe ping time of ≈63 ms. According to this site, that's enough for a smooth connection from Germany to any other place in Europe. At this ping, my system could still run the game without slowdown even if every single frame required a rollback, which is highly unlikely.
Any higher ping, however, could occasionally lead to a rollback queue that's too large for my system to process within a single frame at the intended 56.4 FPS rate. As a result, playing anyone in the US is highly likely to involve at least occasional slowdowns. Delaying inputs on purpose is the usual workaround, but isn't Touhou that kind of game series where people use vpatch to get rid of even the default input delay in the Windows games?
So we'd ideally want to put TH03 into an update-only mode that skips all rendering calls during re-simulation of rolled-back frames. Ironically, this means that netplay-focused RE would actually focus on the game's rendering code and ensure that it doesn't mutate any statically allocated data, allowing it to be freely skipped without affecting the game. Imagine palette-based flashing animations that are implemented by gradually mutating statically allocated values – these would cause wrong colors for the rest of the game if the animation doesn't run on every frame.
Implementing all of this into TH03 can be done in one, a few, or all of the following five ways, depending on what the backers prefer. Sorted from the most generic to the most specialized solution (and, coincidentally, from least to most total effort required):
Generic PC-98 netcode for one or more emulators
This is the most basic and puristic variant that implements generic netplay for PC-98 games in general by effectively providing remote control of the emulated keyboard and joypad. The emulator will be unaware of the game, and the game will be unaware of being netplayed, which makes this solution particularly interesting for the non-Touhou PC-98 scene, or competitive players who absolutely insist on using ZUN's original binaries and won't trust any of my modded game builds.
Applied to TH03, this means that players would select the regular hot-seat 1P vs 2P mode and then initiate a match through a new menu in the emulator UI. The same UI must then provide an option to manually remap incoming key and button presses to the 2P controls (newly introducing remapping to the emulator if necessary), as well as blocking any non-2P keys. The host then sends an initial savestate to the guest to ensure an identical starting state, and starts synchronizing and rolling back inputs at VSync boundaries.
This generic nature means that we don't get to include any of the TH03-specific rollback optimizations mentioned above, leading to the highest CPU and memory requirements out of all the variants. It sure is the easiest to implement though, as we get to freely use modern C++ WebRTC libraries that are designed to work with the network stack of the underlying OS.
I can try to build this netcode as a generic library that can work with any PC-98 emulator, but it would ultimately be up to the respective upstream developers to integrate it into official releases. Therefore, expect this variant to require separate funding and custom builds for each individual emulator codebase that we'd like to support.
Emulator-level netcode with optional game integration
Takes the generic netcode developed in 1) and adds the possibility for the game to control it via a special interrupt API. This enables several improvements:
Online matches could be initiated through new options in TH03's main menu rather than the emulator's UI.
The game could communicate the memory region that should be backed up every frame, cutting down memory usage as described above.
The exchanged input data could use the game's internal format instead of keyboard or joypad inputs. This removes the need for key remapping at the emulator level and naturally prevents the inherent issue of remote control where players could mess with each other's controls.
The game could be aware of the rollbacks, allowing it to jump over its rendering code while processing the queue of remote inputs and thus gain some performance as explained above.
The game could add synchronization points that block gameplay until both players have reached them, preventing the rollback queue from growing infinitely. This solves the issue of 1) not having any inherent way of working around desyncs and the resulting growth of the rollback queue. As an example, if one of the two emulators in 1) took, say, 2 seconds longer to load the game due to a random CPU spike caused by some bloatware on their system, the two players would be out of sync by 2 seconds for the rest of the session, forcing the faster system to render 113 frames every time an input prediction turned out to be incorrect.
Good places for synchronization points include the beginning of each round, the WARNING!! You are forced to evade / Your life is in peril popups that pause the game for a few frames anyway, and whenever the game is paused via the ESC key.
During such pauses, the game could then also block the resuming ESC key of the player who didn't pause the game.
Native PC-98 Windows 9x netcode
Equivalent in features to 2), but pulls the netcode from the emulator down into the PC-98 system itself. Just like Ju.N.Owen or Adonis, it would run as a separate 32-bit or 16-bit Windows application that somehow communicates with the game running in a DOS window. This removes the need for emulator-specific integration code and provides real-hardware support for that handful of real-hardware owners who have actually equipped their PC-98 with a network card such as the LGY-98.
This specific card is also low-level-emulated by the 21/W fork of Neko Project, which would allow this type of netplay to be used with official builds of that specific emulator. DOSBox-X currently emulates the apparently hardware-compatible NE2000 card, but disables its emulation in PC-98 mode, most likely because its I/O ports clash with the typical peripherals of a PC-98 system.
As this is just low-level emulation of a network device though, setting up this kind of networking in Neko Project 21/W requires you to install and configure both a TAP driver on the host system, and the whole Windows 9x network stack on the emulated PC-98. Thankfully, the setup is well-documented, and I did manage to get a working Internet connection inside an emulated Windows 95, but it's definitely not foolproof. A more specific guide or setup program would greatly help here.
And that's not the end of the drawbacks:
Netplay would depend on the PC-98 versions of Windows 9x, requiring players to acquire and install another OS on the emulated system.
Porting libdatachannel (and especially the required transport encryption) to Windows 95 will probably involve a bit of effort as well.
As would actually finding a way to access V86 mode memory from a 32-bit or 16-bit Windows process.
Correctly setting up TH03 to run within Windows 95 to begin with can be rather tricky. The GDC clock speed check needs to be either patched out or overridden using mode-setting tools, Windows needs to be blocked from accessing the FM chip, and even then, MAIN.EXE might still immediately crash during the first frame and leave all of VRAM corrupted:
A matchmaking server would be much more of a requirement than in any of the emulator variants. Players are unlikely to run their favorite chat client on the same PC-98 system, and the signaling codes are way too unwieldy to type them in manually. (Then again, IRC is always an option, and the people who would fund this variant are probably the exact same people who are already running IRC clients on their PC-98.)
Native PC-98 DOS netcode
Conceptually the same as 3), but going yet another level deeper, replacing the Windows 9x network stack with a DOS-based one. This might look even more intimidating and error-prone, but after I got pingand even Telnet working, I was pleasantly surprised at it's much simpler it is when compared to the Windows variant. The whole stack consists of just one LGY-98 hardware information tool, a LGY-98 packet driver TSR, and a TSR that implements TCP/IP/UDP/DNS/ICMP and is configured with a plaintext file. I don't have any deep experience with these protocols, so I was quite surprised that you can implement all of them in a single 40 KiB binary. Installed as TSRs, the entire stack takes up an acceptable 82 KiB of conventional memory, leaving more than enough space for the game itself. And since both of the TSRs are open-source, we can even legally bundle them with the future modified game binaries.
However, all the emulation and matchmaking issues from the Windows 9x approach remain, along with the following issues:
Porting libdatachannel and the required transport encryption to the TEEN stack seems even more time-consuming than a Windows 95 port.
The TEEN stack has no UI for specifying the system's or gateway's IP addresses outside of its plaintext configuration file. This provides a nice opportunity for adding a new Internet settings menu with great error feedback to the game itself. Great for UX, but it's another thing I'd have to write.
Due to the memory requirements of rollback, the netcode should better run as a TSR in Protected Mode, adding yet another technology I'd have to learn about.
The LGY-98 is not the only network card for the PC-98. Others might have more complicated DOS drivers that might not work as seamlessly with the TEEN stack, or have no preserved DOS drivers at all. Heck, the most time-consuming part of the DOS setup was finding the correct download link for the LGY-98 packet driver, as the one link that appears in a lot of places only throws an access denied error these days. If you're interested in funding this variant and are using a non-LGY-98 card on real hardware, make sure you get general Internet working on DOS first.
Porting the game first
As always, this is the premium option. If the entire game already runs as a standalone executable on a modern system, we can just put all the netcode into the same binary and have the most seamless integration possible.
That leaves us with these prerequisites:
1), by definition, needs nothing from ReC98, and I could theoretically start implementing it right now. If you're interested in funding it, just tell me via the usual Twitter or Discord channels.
2), 3), and 4) require at least 100% RE of TH03's OP.EXE to facilitate the new menu code. Reverse-engineering all rendering-related code in MAIN.EXE would be nice for performance, but we don't strictly need all of it before we start. Re-simulated frames can just skip over the few pieces of rendering code we do know, and we can gradually increase the skipped area of code in future pushes.
100% PI won't be a requirement either, as I expect the MAIN.EXE part of the interfacing netcode layer to be thin enough that it can easily fit within the original game's code layout.
5), obviously, requires all of TH03 to be RE'd, decompiled, cleaned up, and ported to modern systems. Currently, TH03 appears to be the second-easiest game to port behind TH02:
Although TH03 already has more needlessly micro-optimized ASM code than TH02 and there's even more to come, it still appears to have way less than TH04 or TH05.
Its game logic and rendering code seem to be somewhat neatly separated from each other, unlike TH01 which deeply intertwines them.
Its graphics seem free of obvious bugs, unlike – again — the flicker-fest that is TH01.
But still, it's the game with the least amount of RE%. Decompilation might get easier once I've worked myself up to the higher levels of game code, and even more so if we're lucky and all of the 9 characters are coded in a similar way, but I can't promise anything at this point.
Once we've reached any of these prerequisites, I'll set up a separate campaign funding method that runs parallel to the cap. As netplay is one of those big features where incremental progress makes little sense and we can expect wide community support for the idea, I'll go for a more classic crowdfunding model with a fixed goal for the minimum feature set and stretch goals for optional quality-of-life features. Since I've still got two other big projects waiting to be finished, I'd like to at least complete the Shuusou Gyoku Linux port before I start working on TH03 netplay, even if we manage to hit any of the funding goals before that.
For the first time in a long while, the actual content of this push can be listed fairly quickly. I've now RE'd:
conversions from playfield-relative coordinates to screen coordinates and back (a first in PC-98 Touhou; even TH02 uses screen space for every coordinate I've seen so far),
the low-level code that moves the player entity across the screen,
a copy of the per-round frame counter that, for some reason, resets to 0 at the start of the Win/Lose animation, resetting a bunch of animations with it,
a global hitbox with one variable that sometimes stores the center of an entity, and sometimes its top-left corner,
and the 48×48 hit circles from EN2.PI.
It's also the third TH03 gameplay push in a row that features inappropriate ASM code in places that really, really didn't need any. As usual, the code is worse than what Turbo C++ 4.0J would generate for idiomatic C code, and the surrounding code remains full of untapped and quick optimization opportunities anyway. This time, the biggest joke is the sprite offset calculation in the hit circle rendering code:
But while we've all come to expect the usual share of ZUN bloat by now, this is also the first push without either a ZUN bug or a landmine since I started using these terms! 🎉 It does contain a single ZUN quirk though, which can also be found in the hit circles. This animation comes in two types with different caps: 12 animation slots across both playfields for the enemy circles shown in alternating bright/dark yellow colors, whereas the white animation for the player characters has a cap of… 1? P2 takes precedence over P1 because its update code always runs last, which explains what happens when both players get hit within the 16 frames of the animation:
SPRITE16 uses the PC-98's EGC to draw these single-color sprites. If the EGC is already set up, it can be set into a GRCG-equivalent RMW mode using the pattern/read plane register (0x4A2) and foreground color register (0x4A6), together with setting the mode register (0x4A4) to 0x0CAC. Unlike the typical blitting operations that involve its 16-dot pattern register, the EGC even supports 8- or 32-bit writes in this mode, just like the GRCG. 📝 As expected for EGC features beyond the most ordinary ones though, T98-Next simply sets every written pixel to black on a 32-bit write. Comparing the actual performance of such writes to the GRCG would be 📝 yet another interesting question to benchmark.
Next up: I think it's time for ReC98's build system to reach its final form.
For almost 5 years, I've been using an unreleased sane build system on a parallel private branch that was just missing some final polish and bugfixes. Meanwhile, the public repo is still using the project's initial Makefile that, 📝 as typical for Makefiles, is so unreliable that BUILD16B.BAT force-rebuilds everything by default anyway. While my build system has scaled decently over the years, something even better happened in the meantime: MS-DOS Player, a DOS emulator exclusively meant for seamless integration of CLI programs into the Windows console, has been forked and enhanced enough to finally run Turbo C++ 4.0J at an acceptable speed. So let's remove DOSBox from the equation, merge the 32-bit and 16-bit build steps into a single 32-bit one, set all of this up in a user-friendly way, and maybe squeeze even more performance out of MS-DOS Player specifically for this use case.
Well, well. My original plan was to ship the first step of Shuusou Gyoku
OpenGL support on the next day after this delivery. But unfortunately, the
complications just kept piling up, to a point where the required solutions
definitely blow the current budget for that goal. I'm currently sitting on
over 70 commits that would take at least 5 pushes to deliver as a meaningful
release, and all of that is just rearchitecting work, preparing the
game for a not too Windows-specific OpenGL backend in the first place. I
haven't even written a single line of OpenGL yet… 🥲
This shifts the intended Big Release Month™ to June after all. Now I know
that the next round of Shuusou Gyoku features should better start with the
SC-88Pro recordings, which are much more likely to get done within their
current budget. At least I've already completed the configuration versioning
system required for that goal, which leaves only the actual audio part.
So, TH04 position independence. Thanks to a bit of funding for stage
dialogue RE, non-ASCII translations will soon become viable, which finally
presents a reason to push TH04 to 100% position independence after
📝 TH05 had been there for almost 3 years. I
haven't heard back from Touhou Patch Center about how much they want to be
involved in funding this goal, if at all, but maybe other backers are
interested as well.
And sure, it would be entirely possible to implement non-ASCII translations
in a way that retains the layout of the original binaries and can be easily
compared at a binary level, in case we consider translations to be a
critical piece of infrastructure. This wouldn't even just be an exercise in
needless perfectionism, and we only have to look to Shuusou Gyoku to realize
why: Players expected
that my builds were compatible with existing SpoilerAL SSG files, which
was something I hadn't even considered the need for. I mean, the game is
open-source 📝 and I made it easy to build.
You can just fork the code, implement all the practice features you want in
a much more efficient way, and I'd probably even merge your code into my
builds then?
But I get it – recompiling the game yields just yet another build that can't
be easily compared to the original release. A cheat table is much more
trustworthy in giving players the confidence that they're still practicing
the same original game. And given the current priorities of my backers,
it'll still take a while for me to implement proof by replay validation,
which will ultimately free every part of the community from depending on the
original builds of both Seihou and PC-98 Touhou.
However, such an implementation within the original binary layout would
significantly drive up the budget of non-ASCII translations, and I sure
don't want to constantly maintain this layout during development. So, let's
chase TH04 position independence like it's 2020, and quickly cover a larger
amount of PI-relevant structures and functions at a shallow level. The only
parts I decompiled for now contain calculations whose intent can't be
clearly communicated in ASM. Hitbox visualizations or other more in-depth
research would have to wait until I get to the proper decompilation of these
features.
But even this shallow work left us with a large amount of TH04-exclusive
code that had its worst parts RE'd and could be decompiled fairly quickly.
If you want to see big TH04 finalization% gains, general TH04 progress would
be a very good investment.
The first push went to the often-mentioned stage-specific custom entities
that share a single statically allocated buffer. Back in 2020, I
📝 wrongly claimed that these were a TH05 innovation,
but the system actually originated in TH04. Both games use a 26-byte
structure, but TH04 only allocates a 32-element array rather than TH05's
64-element one. The conclusions from back then still apply, but I also kept
wondering why these games used a static array for these entities to begin
with. You know what they call an area of memory that you can cleanly
repurpose for things? That's right, a heap!
And absolutely no one would mind one additional heap allocation at the start
of a stage, next to the ones for all the sprites and portraits.
However, we are still running in Real Mode with segmented memory. Accessing
anything outside a common data segment involves modifying segment registers,
which has a nonzero CPU cycle cost, and Turbo C++ 4.0J is terrible at
optimizing away the respective instructions. Does this matter? Probably not,
but you don't take "risks" like these if you're in a permanent
micro-optimization mindset…
In TH04, this system is used for:
Kurumi's symmetric bullet spawn rays, fired from her hands towards the left
and right edges of the playfield. These are rather infamous for being the
last thing you see before
📝 the Divide Error crash that can happen in ZUN's original build.
Capped to 6 entities.
The 4 📝 bits used in Marisa's Stage 4 boss
fight. Coincidentally also related to the rare Divide Error
crash in that fight.
Stage 4 Reimu's spinning orbs. Note how the game uses two different sets
of sprites just to have two different outline colors. This was probably
better than messing with the palette, which can easily cause unintended
effects if you only have 16 colors to work with. Heck, I have an entire blog post tag just to highlight
these cases. Capped to the full 32 entities.
The chasing cross bullets, seen in Phase 14 of the same Stage 6 Yuuka
fight. Featuring some smart sprite work, making use of point symmetry to
achieve a fluid animation in just 4 frames. This is
good-code in sprite form. Capped to 31 entities, because the 32nd custom entity during this fight is defined to be…
The single purple pulsating and shrinking safety circle, seen in Phase 4 of
the same fight. The most interesting aspect here is actually still related
to the cross bullets, whose spawn function is wrongly limited to 32 entities
and could theoretically overwrite this circle. This
is strictly landmine territory though:
Yuuka never uses these bullets and the safety circle
simultaneously
She never spawns more than 24 cross bullets
All cross bullets are fast enough to have left the screen by the
time Yuuka restarts the corresponding subpattern
The cross bullets spawn at Yuuka's center position, and assign its
Q12.4 coordinates to structure fields that the safety circle interprets
as raw pixels. The game does try to render the circle afterward, but
since Yuuka's static position during this phase is nowhere near a valid
pixel coordinate, it is immediately clipped.
The flashing lines seen in Phase 5 of the Gengetsu fight,
telegraphing the slightly random bullet columns.
These structures only took 1 push to reverse-engineer rather than the 2 I
needed for their TH05 counterparts because they are much simpler in this
game. The "structure" for Gengetsu's lines literally uses just a single X
position, with the remaining 24 bytes being basically padding. The only
minor bug I found on this shallow level concerns Marisa's bits, which are
clipped at the right and bottom edges of the playfield 16 pixels earlier
than you would expect:
The remaining push went to a bunch of smaller structures and functions:
The structure for the up to 2 "thick" (a.k.a. "Master Spark") lasers. Much
saner than the
📝 madness of TH05's laser system while being
equally customizable in width and duration.
The structure for the various monochrome 16×16 shapes in the background of
the Stage 6 Yuuka fight, drawn on top of the checkerboard.
The rendering code for the three falling stars in the background of Stage 5.
The effect here is entirely palette-related: After blitting the stage tiles,
the 📝 1bpp star image is ORed
into only the 4th VRAM plane, which is equivalent to setting the
highest bit in the palette color index of every pixel within the star-shaped
region. This of course raises the question of how the stage would look like
if it was fully illuminated:
Most code that modifies a stage's tile map, and directly specifies tiles via
their top-left offset in VRAM.
Thanks to code alignment reasons, this forced a much longer detour into the
.STD format loader. Nothing all too noteworthy there since we're still
missing the enemy script and spawn structures before we can call .STD
"reverse-engineered", but maybe still helpful if you're looking for an
overview of the format. Also features a buffer overflow landmine if a .STD
file happens to contain more than 32 enemy scripts… you know, the usual
stuff.
To top off the second push, we've got the vertically scrolling checkerboard
background during the Stage 6 Yuuka fight, made up of 32×32 squares. This
one deserves a special highlight just because of its needless complexity.
You'd think that even a performant implementation would be pretty simple:
Set the GRCG to TDW mode
Set the GRCG tile to one of the two square colors
Start with Y as the current scroll offset, and X
as some indicator of which color is currently shown at the start of each row
of squares
Iterate over all lines of the playfield, filling in all pixels that
should be displayed in the current color, skipping over the other ones
Count down Y for each line drawn
If Y reaches 0, reset it to 32 and flip X
At the bottom of the playfield, change the GRCG tile to the other color,
and repeat with the initial value of X flipped
The most important aspect of this algorithm is how it reduces GRCG state
changes to a minimum, avoiding the costly port I/O that we've identified
time and time again as one of the main bottlenecks in TH01. With just 2
state variables and 3 loops, the resulting code isn't that complex either. A
naive implementation that just drew the squares from top to bottom in a
single pass would barely be simpler, but much slower: By changing the GRCG
tile on every color, such an implementation would burn a low 5-digit number
of CPU cycles per frame for the 12×11.5-square checkerboard used in the
game.
And indeed, ZUN retained all important aspects of this algorithm… but still
implemented it all in ASM, with a ridiculous layer of x86 segment arithmetic
on top? Which blows up the complexity to 4 state
variables, 5 nested loops, and a bunch of constants in unusual units. I'm
not sure what this code is supposed to optimize for, especially with that
rather questionable register allocation that nevertheless leaves one of the
general-purpose registers unused. Fortunately,
the function was still decompilable without too many code generation hacks,
and retains the 5 nested loops in all their goto-connected
glory. If you want to add a checkerboard to your next PC-98
demo, just stick to the algorithm I gave above.
(Using a single XOR for flipping the starting X offset between 32 and 64
pixels is pretty nice though, I have to give him that.)
This makes for a good occasion to talk about the third and final GRCG mode,
completing the series I started with my previous coverage of the
📝 RMW and
📝 TCR modes. The TDW (Tile Data Write) mode
is the simplest of the three and just writes the 8×1 GRCG tile into VRAM
as-is, without applying any alpha bitmask. This makes it perfect for
clearing rectangular areas of pixels – or even all of VRAM by doing a single
memset():
// Set up the GRCG in TDW mode.
outportb(0x7C, 0x80);
// Fill the tile register with color #7 (0111 in binary).
outportb(0x7E, 0xFF); // Plane 0: (B): (********)
outportb(0x7E, 0xFF); // Plane 1: (R): (********)
outportb(0x7E, 0xFF); // Plane 2: (G): (********)
outportb(0x7E, 0x00); // Plane 3: (E): ( )
// Set the 32 pixels at the top-left corner of VRAM to the exact contents of
// the tile register, effectively repeating the tile 4 times. In TDW mode, the
// GRCG ignores the CPU-supplied operand, so we might as well just pass the
// contents of a register with the intended width. This eliminates useless load
// instructions in the compiled assembly, and even sort of signals to readers
// of this code that we do not care about the source value.
*reinterpret_cast<uint32_t far *>(MK_FP(0xA800, 0)) = _EAX;
// Fill the entirety of VRAM with the GRCG tile. A simple C one-liner that will
// probably compile into a single `REP STOS` instruction. Unfortunately, Turbo
// C++ 4.0J only ever generates the 16-bit `REP STOSW` here, even when using
// the `__memset__` intrinsic and when compiling in 386 mode. When targeting
// that CPU and above, you'd ideally want `REP STOSD` for twice the speed.
memset(MK_FP(0xA800, 0), _AL, ((640 / 8) * 400));
However, this might make you wonder why TDW mode is even necessary. If it's
functionally equivalent to RMW mode with a CPU-supplied bitmask made up
entirely of 1 bits (i.e., 0xFF, 0xFFFF, or
0xFFFFFFFF), what's the point? The difference lies in the
hardware implementation: If all you need to do is write tile data to
VRAM, you don't need the read and modify parts of RMW mode
which require additional processing time. The PC-9801 Programmers'
Bible claims a speedup of almost 2× when using TDW mode over equivalent
operations in RMW mode.
And that's the only performance claim I found, because none of these old
PC-98 hardware and programming books did any benchmarks. Then again, it's
not too interesting of a question to benchmark either, as the byte-aligned
nature of TDW blitting severely limits its use in a game engine anyway.
Sure, maybe it makes sense to temporarily switch from RMW to TDW mode
if you've identified a large rectangular and byte-aligned section within a
sprite that could be blitted without a bitmask? But the necessary
identification work likely nullifies the performance gained from TDW mode,
I'd say. In any case, that's pretty deep
micro-optimization territory. Just use TDW mode for the
few cases it's good at, and stick to RMW mode for the rest.
So is this all that can be said about the GRCG? Not quite, because there are
4 bits I haven't talked about yet…
And now we're just 5.37% away from 100% position independence for TH04! From
this point, another 2 pushes should be enough to reach this goal. It might
not look like we're that close based on the current estimate, but a
big chunk of the remaining numbers are false positives from the player shot
control functions. Since we've got a very special deadline to hit, I'm going
to cobble these two pushes together from the two current general
subscriptions and the rest of the backlog. But you can, of course, still
invest in this goal to allow the existing contributions to go to something
else.
… Well, if the store was actually open. So I'd better
continue with a quick task to free up some capacity sooner rather than
later. Next up, therefore: Back to TH02, and its item and player systems.
Shouldn't take that long, I'm not expecting any surprises there. (Yeah, I
know, famous last words…)
More than three months without any reverse-engineering progress! It's been
way too long. Coincidentally, we're at least back with a surprising 1.25% of
overall RE, achieved within just 3 pushes. The ending script system is not
only more or less the same in TH04 and TH05, but actually originated in
TH03, where it's also used for the cutscenes before stages 8 and 9. This
means that it was one of the final pieces of code shared between three of
the four remaining games, which I got to decompile at roughly 3× the usual
speed, or ⅓ of the price.
The only other bargains of this nature remain in OP.EXE. The
Music Room is largely equivalent in all three remaining games as well, and
the sound device selection, ZUN Soft logo screens, and main/option menus are
the same in TH04 and TH05. A lot of that code is in the "technically RE'd
but not yet decompiled" ASM form though, so it would shift Finalized% more
significantly than RE%. Therefore, make sure to order the new
Finalization option rather than Reverse-engineering if you
want to make number go up.
So, cutscenes. On the surface, the .TXT files look simple enough: You
directly write the text that should appear on the screen into the file
without any special markup, and add commands to define visuals, music, and
other effects at any place within the script. Let's start with the basics of
how text is rendered, which are the same in all three games:
First off, the text area has a size of 480×64 pixels. This means that it
does not correspond to the tiled area painted into TH05's
EDBK?.PI images:
Since the font weight can be customized, all text is rendered to VRAM.
This also includes gaiji, despite them ignoring the font weight
setting.
The system supports automatic line breaks on a per-glyph basis, which
move the text cursor to the beginning of the red text area. This might seem like a piece of long-forgotten
ancient wisdom at first, considering the absence of automatic line breaks in
Windows Touhou. However, ZUN probably implemented it more out of pure
necessity: Text in VRAM needs to be unblitted when starting a new box, which
is way more straightforward and performant if you only need to worry
about a fixed area.
The system also automatically starts a new (key press-separated) text
box after the end of the 4th line. However, the text cursor is
also unconditionally moved to the top-left corner of the yellow name
area when this happens, which is almost certainly not what you expect, given
that automatic line breaks stay within the red area. A script author might
as well add the necessary text box change commands manually, if you're
forced to anticipate the automatic ones anyway…
Due to ZUN forgetting an unblitting call during the TH05 refactoring of the
box background buffer, this feature is even completely broken in that game,
as any new text will simply be blitted on top of the old one:
Overall, the system is geared toward exclusively full-width text. As
exemplified by the 2014 static English patches and the screenshots in this
blog post, half-width text is possible, but comes with a lot of
asterisks attached:
Each loop of the script interpreter starts by looking at the next
byte to distinguish commands from text. However, this step also skips
over every ASCII space and control character, i.e., every byte
≤ 32. If you only intend to display full-width glyphs anyway, this
sort of makes sense: You gain complete freedom when it comes to the
physical layout of these script files, and it especially allows commands
to be freely separated with spaces and line breaks for improved
readability. Still, enforcing commands to be separated exclusively by
line breaks might have been even better for readability, and would have
freed up ASCII spaces for regular text…
Non-command text is blindly processed and rendered two bytes at a
time. The rendering function interprets these bytes as a Shift-JIS
string, so you can use half-width characters here. While the
second byte can even be an ASCII 0x20 space due to the
parser's blindness, all half-width characters must still occur in pairs
that can't be interrupted by commands:
As a workaround for at least the ASCII space issue, you can replace
them with any of the unassigned
Shift-JIS lead bytes – 0x80, 0xA0, or
anything between 0xF0 and 0xFF inclusive.
That's what you see in all screenshots of this post that display
half-width spaces.
Finally, did you know that you can hold ESC to fast-forward
through these cutscenes, which skips most frame delays and reduces the rest?
Due to the blocking nature of all commands, the ESC key state is
only updated between commands or 2-byte text groups though, so it can't
interrupt an ongoing delay.
Superficially, the list of game-specific differences doesn't look too long,
and can be summarized in a rather short table:
It's when you get into the implementation that the combined three systems
reveal themselves as a giant mess, with more like 56 differences between the
games. Every single new weird line of code opened up
another can of worms, which ultimately made all of this end up with 24
pieces of bloat and 14 bugs. The worst of these should be quite interesting
for the general PC-98 homebrew developers among my audience:
The final official 0.23 release of master.lib has a bug in
graph_gaiji_put*(). To calculate the JIS X 0208 code point for
a gaiji, it is enough to ADD 5680h onto the gaiji ID. However,
these functions accidentally use ADC instead, which incorrectly
adds the x86 carry flag on top, causing weird off-by-one errors based on the
previous program state. ZUN did fix this bug directly inside master.lib for
TH04 and TH05, but still needed to work around it in TH03 by subtracting 1
from the intended gaiji ID. Anyone up for maintaining a bug-fixed master.lib
repository?
The worst piece of bloat comes from TH03 and TH04 needlessly
switching the visibility of VRAM pages while blitting a new 320×200 picture.
This makes it much harder to understand the code, as the mere existence of
these page switches is enough to suggest a more complex interplay between
the two VRAM pages which doesn't actually exist. Outside this visibility
switch, page 0 is always supposed to be shown, and page 1 is always used
for temporarily storing pixels that are later crossfaded onto page 0. This
is also the only reason why TH03 has to render text and gaiji onto both VRAM
pages to begin with… and because TH04 doesn't, changing the picture in the
middle of a string of text is technically bugged in that game, even though
you only get to temporarily see the new text on very underclocked PC-98
systems.
These performance implications made me wonder why cutscenes even bother with
writing to the second VRAM page anyway, before copying each crossfade step
to the visible one.
📝 We learned in June how costly EGC-"accelerated" inter-page copies are;
shouldn't it be faster to just blit the image once rather than twice?
Well, master.lib decodes .PI images into a packed-pixel format, and
unpacking such a representation into bitplanes on the fly is just about the
worst way of blitting you could possibly imagine on a PC-98. EGC inter-page
copies are already fairly disappointing at 42 cycles for every 16 pixels, if
we look at the i486 and ignore VRAM latencies. But under the same
conditions, packed-pixel unpacking comes in at 81 cycles for every 8
pixels, or almost 4× slower. On lower-end systems, that can easily sum up to
more than one frame for a 320×200 image. While I'd argue that the resulting
tearing could have been an acceptable part of the transition between two
images, it's understandable why you'd want to avoid it in favor of the
pure effect on a slower framerate.
Really makes me wonder why master.lib didn't just directly decode .PI images
into bitplanes. The performance impact on load times should have been
negligible? It's such a good format for
the often dithered 16-color artwork you typically see on PC-98, and
deserves better than master.lib's implementation which is both slow to
decode and slow to blit.
That brings us to the individual script commands… and yes, I'm going to
document every single one of them. Some of their interactions and edge cases
are not clear at all from just looking at the code.
Almost all commands are preceded by… well, a 0x5C lead byte.
Which raises the question of whether we should
document it as an ASCII-encoded \ backslash, or a Shift-JIS-encoded
¥ yen sign. From a gaijin perspective, it seems obvious that it's a
backslash, as it's consistently displayed as one in most of the editors you
would actually use nowadays. But interestingly, iconv
-f shift-jis -t utf-8 does convert any 0x5C
lead bytes to actual ¥ U+00A5 YEN SIGN code points
.
Ultimately, the distinction comes down to the font. There are fonts
that still render 0x5C as ¥, but mainly do so out
of an obvious concern about backward compatibility to JIS X 0201, where this
mapping originated. Unsurprisingly, this group includes MS Gothic/Mincho,
the old Japanese fonts from Windows 3.1, but even Meiryo and Yu
Gothic/Mincho, Microsoft's modern Japanese fonts. Meanwhile, pretty much
every other modern font, and freely licensed ones in particular, render this
code point as \, even if you set your editor to Shift-JIS. And
while ZUN most definitely saw it as a ¥, documenting this code
point as \ is less ambiguous in the long run. It can only
possibly correspond to one specific code point in either Shift-JIS or UTF-8,
and will remain correct even if we later mod the cutscene system to support
full-blown Unicode.
Now we've only got to clarify the parameter syntax, and then we can look at
the big table of commands:
Numeric parameters are read as sequences of up to 3 ASCII digits. This
limits them to a range from 0 to 999 inclusive, with 000 and
0 being equivalent. Because there's no further sentinel
character, any further digit from the 4th one onwards is
interpreted as regular text.
Filename parameters must be terminated with a space or newline and are
limited to 12 characters, which translates to 8.3 basenames without any
directory component. Any further characters are ignored and displayed as
text as well.
Each .PI image can contain up to four 320×200 pictures ("quarters") for
the cutscene picture area. In the script commands, they are numbered like
this:
0
1
2
3
\@
Clears both VRAM pages by filling them with VRAM color 0. 🐞
In TH03 and TH04, this command does not update the internal text area
background used for unblitting. This bug effectively restricts usage of
this command to either the beginning of a script (before the first
background image is shown) or its end (after no more new text boxes are
started). See the image below for an
example of using it anywhere else.
\b2
Sets the font weight to a value between 0 (raw font ROM glyphs) to 3
(very thicc). Specifying any other value has no effect.
🐞 In TH04 and TH05, \b3 leads to glitched pixels when
rendering half-width glyphs due to a bug in the newly micro-optimized
ASM version of
📝 graph_putsa_fx(); see the image below for an example.
In these games, the parameter also directly corresponds to the
graph_putsa_fx() effect function, removing the sanity check
that was present in TH03. In exchange, you can also access the four
dissolve masks for the bold font (\b2) by specifying a
parameter between 4 (fewest pixels) to 7 (most
pixels). Demo video below.
\c15
Changes the text color to VRAM color 15.
\c=字,15
Adds a color map entry: If 字 is the first code point
inside the name area on a new line, the text color is automatically set
to 15. Up to 8 such entries can be registered
before overflowing the statically allocated buffer.
🐞 The comma is assumed to be present even if the color parameter is omitted.
\e0
Plays the sound effect with the given ID.
\f
(no-op)
\fi1
\fo1
Calls master.lib's palette_black_in() or
palette_black_out() to play a hardware palette fade
animation from or to black, spending roughly 1 frame on each of the 16 fade steps.
\fm1
Fades out BGM volume via PMD's AH=02h interrupt call,
in a non-blocking way. The fade speed can range from 1 (slowest) to 127 (fastest).
Values from 128 to 255 technically correspond to
AH=02h's fade-in feature, which can't be used from cutscene
scripts because it requires BGM volume to first be lowered via
AH=19h, and there is no command to do that.
\g8
Plays a blocking 8-frame screen shake
animation.
\ga0
Shows the gaiji with the given ID from 0 to 255
at the current cursor position. Even in TH03, gaiji always ignore the
text delay interval configured with \v.
@3
TH05's replacement for the \ga command from TH03 and
TH04. The default ID of 3 corresponds to the
gaiji. Not to be confused with \@, which starts with a backslash,
unlike this command.
@h
Shows the gaiji.
@t
Shows the gaiji.
@!
Shows the gaiji.
@?
Shows the gaiji.
@!!
Shows the gaiji.
@!?
Shows the gaiji.
\k0
Waits 0 frames (0 = forever) for an advance key to be pressed before
continuing script execution. Before waiting, TH05 crossfades in any new
text that was previously rendered to the invisible VRAM page…
🐞 …but TH04 doesn't, leaving the text invisible during the wait time.
As a workaround, \vp1 can be
used before \k to immediately display that text without a
fade-in animation.
\m$
Stops the currently playing BGM.
\m*
Restarts playback of the currently loaded BGM from the
beginning.
\m,filename
Stops the currently playing BGM, loads a new one from the given
file, and starts playback.
\n
Starts a new line at the leftmost X coordinate of the box, i.e., the
start of the name area. This is how scripts can "change" the name of the
currently speaking character, or use the entire 480×64 pixels without
being restricted to the non-name area.
Note that automatic line breaks already move the cursor into a new line.
Using this command at the "end" of a line with the maximum number of 30
full-width glyphs would therefore start a second new line and leave the
previously started line empty.
If this command moved the cursor into the 5th line of a box,
\s is executed afterward, with
any of \n's parameters passed to \s.
\p
(no-op)
\p-
Deallocates the loaded .PI image.
\p,filename
Loads the .PI image with the given file into the single .PI slot
available to cutscenes. TH04 and TH05 automatically deallocate any
previous image, 🐞 TH03 would leak memory without a manual prior call to
\p-.
\pp
Sets the hardware palette to the one of the loaded .PI image.
\p@
Sets the loaded .PI image as the full-screen 640×400 background
image and overwrites both VRAM pages with its pixels, retaining the
current hardware palette.
\p=
Runs \pp followed by \p@.
\s0
\s-
Ends a text box and starts a new one. Fades in any text rendered to
the invisible VRAM page, then waits 0 frames
(0 = forever) for an advance key to be
pressed. Afterward, the new text box is started with the cursor moved to
the top-left corner of the name area. \s- skips the wait time and starts the new box
immediately.
\t100
Sets palette brightness via master.lib's
palette_settone() to any value from 0 (fully black) to 200
(fully white). 100 corresponds to the palette's original colors.
Preceded by a 1-frame delay unless ESC is held.
\v1
Sets the number of frames to wait between every 2 bytes of rendered
text.
Sets the number of frames to spend on each of the 4 fade
steps when crossfading between old and new text. The game-specific
default value is also used before the first use of this command.
\v2
\vp0
Shows VRAM page 0. Completely useless in
TH03 (this game always synchronizes both VRAM pages at a command
boundary), only of dubious use in TH04 (for working around a bug in \k), and the games always return to
their intended shown page before every blitting operation anyway. A
debloated mod of this game would just remove this command, as it exposes
an implementation detail that script authors should not need to worry
about. None of the original scripts use it anyway.
\w64
\w and \wk wait for the given number
of frames
\wm and \wmk wait until PMD has played
back the current BGM for the total number of measures, including
loops, given in the first parameter, and fall back on calling
\w and \wk with the second parameter as
the frame number if BGM is disabled.
🐞 Neither PMD nor MMD reset the internal measure when stopping
playback. If no BGM is playing and the previous BGM hasn't been
played back for at least the given number of measures, this command
will deadlock.
Since both TH04 and TH05 fade in any new text from the invisible VRAM
page, these commands can be used to simulate TH03's typing effect in
those games. Demo video below.
Contrary to \k and \s, specifying 0 frames would
simply remove any frame delay instead of waiting forever.
The TH03-exclusive k variants allow the delay to be
interrupted if ⏎ Return or Shot are held down.
TH04 and TH05 recognize the k as well, but removed its
functionality.
All of these commands have no effect if ESC is held.
\wm64,64
\wk64
\wmk64,64
\wi1
\wo1
Calls master.lib's palette_white_in() or
palette_white_out() to play a hardware palette fade
animation from or to white, spending roughly 1 frame on each of the 16 fade steps.
\=4
Immediately displays the given quarter of the loaded .PI image in
the picture area, with no fade effect. Any value ≥ 4 resets the picture area to black.
\==4,1
Crossfades the picture area between its current content and quarter
#4 of the loaded .PI image, spending 1 frame on each of the 4 fade steps unless
ESC is held. Any value ≥ 4 is
replaced with quarter #0.
\$
Stops script execution. Must be called at the end of each file;
otherwise, execution continues into whatever lies after the script
buffer in memory.
TH05 automatically deallocates the loaded .PI image, TH03 and TH04
require a separate manual call to \p- to not leak its memory.
Bold values signify the default if the parameter
is omitted; \c is therefore
equivalent to \c15.
So yeah, that's the cutscene system. I'm dreading the moment I will have to
deal with the other command interpreter in these games, i.e., the
stage enemy system. Luckily, that one is completely disconnected from any
other system, so I won't have to deal with it until we're close to finishing
MAIN.EXE… that is, unless someone requests it before. And it
won't involve text encodings or unblitting…
The cutscene system got me thinking in greater detail about how I would
implement translations, being one of the main dependencies behind them. This
goal has been on the order form for a while and could soon be implemented
for these cutscenes, with 100% PI being right around the corner for the TH03
and TH04 cutscene executables.
Once we're there, the "Virgin" old-school way of static translation patching
for Latin-script languages could be implemented fairly quickly:
Establish basic UTF-8 parsing for less painful manual editing of the
source files
Procedurally generate glyphs for the few required additional letters
based on existing font ROM glyphs. For example, we'd generate ä
by painting two short lines on top of the font ROM's a glyph,
or generate ¿ by vertically flipping the question mark. This
way, the text retains a consistent look regardless of whether the translated
game is run with an NEC or EPSON font ROM, or the that Neko Project II auto-generates if you
don't provide either.
(Optional) Change automatic line breaks to work on a per-word
basis, rather than per-glyph
That's it – script editing and distribution would be handled by your local
translation group. It might seem as if this would also work for Greek and
Cyrillic scripts due to their presence in the PC-98 font ROM, but I'm not
sure if I want to attempt procedurally shrinking these glyphs from 16×16 to
8×16… For any more thorough solution, we'd need to go for a more "Chad" kind
of full-blown translation support:
Implement text subdivisions at a sensible granularity while retaining
automatic line and box breaks
Compile translatable text into a Japanese→target language dictionary
(I'm too old to develop any further translation systems that would overwrite
modded source text with translations of the original text)
Implement a custom Unicode font system (glyphs would be taken from GNU
Unifont unless translators provide a different 8×16 font for their
language)
Combine the text compiler with the font compiler to only store needed
glyphs as part of the translation's font file (dealing with a multi-MB font
file would be rather ugly in a Real Mode game)
Write a simple install/update/patch stacking tool that supports both
.HDI and raw-file DOSBox-X scenarios (it's different enough from thcrap to
warrant a separate tool – each patch stack would be statically compiled into
a single package file in the game's directory)
Add a nice language selection option to the main menu
(Optional) Support proportional fonts
Which sounds more like a separate project to be commissioned from
Touhou Patch Center's Open Collective funds, separate from the ReC98 cap.
This way, we can make sure that the feature is completely implemented, and I
can talk with every interested translator to make sure that their language
works.
It's still cheaper overall to do this on PC-98 than to first port the games
to a modern system and then translate them. On the other hand, most
of the tasks in the Chad variant (3, 4, 5, and half of 2) purely deal with
the difficulty of getting arbitrary Unicode characters to work natively in a
PC-98 DOS game at all, and would be either unnecessary or trivial if we had
already ported the game. Depending on where the patrons' interests lie, it
may not be worth it. So let's see what all of you think about which
way we should go, or whether it's worth doing at all. (Edit
(2022-12-01): With Splashman's
order towards the stage dialogue system, we've pretty much confirmed that it
is.) Maybe we want to meet in the middle – using e.g. procedural glyph
generation for dynamic translations to keep text rendering consistent with
the rest of the PC-98 system, and just not support non-Latin-script
languages in the beginning? In any case, I've added both options to the
order form. Edit (2023-07-28):Touhou Patch Center has agreed to fund
a basic feature set somewhere between the Virgin and Chad level. Check the
📝 dedicated announcement blog post for more
details and ideas, and to find out how you can support this goal!
Surprisingly, there was still a bit of RE work left in the third push after
all of this, which I filled with some small rendering boilerplate. Since I
also wanted to include TH02's playfield overlay functions,
1/15 of that last push went towards getting a
TH02-exclusive function out of the way, which also ended up including that
game in this delivery.
The other small function pointed out how TH05's Stage 5 midboss pops into
the playfield quite suddenly, since its clipping test thinks it's only 32
pixels tall rather than 64:
Next up: Staying with TH05 and looking at more of the pattern code of its
boss fights. Given the remaining TH05 budget, it makes the most sense to
continue in in-game order, with Sara and the Stage 2 midboss. If more money
comes in towards this goal, I could alternatively go for the Mai & Yuki
fight and immediately develop a pretty fix for the cheeto storage
glitch. Also, there's a rather intricate
pull request for direct ZMBV decoding on the website that I've still got
to review…
Alright, back to continuing the master.hpp transition started
in P0124, and repaying technical debt. The last blog post already
announced some ridiculous decompilations… and in fact, not a single
one of the functions in these two pushes was decompilable into
idiomatic C/C++ code.
As usual, that didn't keep me from trying though. The TH04 and TH05
version of the infamous 16-pixel-aligned, EGC-accelerated rectangle
blitting function from page 1 to page 0 was fairly average as far as
unreasonable decompilations are concerned.
The big blocker in TH03's MAIN.EXE, however, turned out to be
the .MRS functions, used to render the gauge attack portraits and bomb
backgrounds. The blitting code there uses the additional FS and GS segment
registers provided by the Intel 386… which
are not supported by Turbo C++'s inline assembler, and
can't be turned into pointers, due to a compiler bug in Turbo C++ that
generates wrong segment prefix opcodes for the _FS and
_GS pseudo-registers.
Apparently I'm the first one to even try doing that with this compiler? I
haven't found any other mention of this bug…
Compiling via assembly (#pragma inline) would work around
this bug and generate the correct instructions. But that would incur yet
another dependency on a 16-bit TASM, for something honestly quite
insignificant.
What we can always do, however, is using __emit__() to simply
output x86 opcodes anywhere in a function. Unlike spelled-out inline
assembly, that can even be used in helper functions that are supposed to
inline… which does in fact allow us to fully abstract away this compiler
bug. Regular if() comparisons with pseudo-registers
wouldn't inline, but "converting" them into C++ template function
specializations does. All that's left is some C preprocessor abuse
to turn the pseudo-registers into types, and then we do retain a
normal-looking poke() call in the blitting functions in the
end. 🤯
Yeah… the result is
batshitinsane.
I may have gone too far in a few places…
One might certainly argue that all these ridiculous decompilations
actually hurt the preservation angle of this project. "Clearly, ZUN
couldn't have possibly written such unreasonable C++ code.
So why pretend he did, and not just keep it all in its more natural ASM
form?" Well, there are several reasons:
Future port authors will merely have to translate all the
pseudo-registers and inline assembly to C++. For the former, this is
typically as easy as replacing them with newly declared local variables. No
need to bother with function prolog and epilog code, calling conventions, or
the build system.
No duplication of constants and structures in ASM land.
As a more expressive language, C++ can document the code much better.
Meticulous documentation seems to have become the main attraction of ReC98
these days – I've seen it appreciated quite a number of times, and the
continued financial support of all the backers speaks volumes. Mods, on the
other hand, are still a rather rare sight.
Having as few .ASM files in the source tree as possible looks better to
casual visitors who just look at GitHub's repo language breakdown. This way,
ReC98 will also turn from an "Assembly project" to its rightful state
of "C++ project" much sooner.
And finally, it's not like the ASM versions are
gone – they're still part of the Git history.
Unfortunately, these pushes also demonstrated a second disadvantage in
trying to decompile everything possible: Since Turbo C++ lacks TASM's
fine-grained ability to enforce code alignment on certain multiples of
bytes, it might actually be unfeasible to link in a C-compiled object file
at its intended original position in some of the .EXE files it's used in.
Which… you're only going to notice once you encounter such a case. Due to
the slightly jumbled order of functions in the
📝 second, shared code segment, that might
be long after you decompiled and successfully linked in the function
everywhere else.
And then you'll have to throw away that decompilation after all 😕 Oh
well. In this specific case (the lookup table generator for horizontally
flipping images), that decompilation was a mess anyway, and probably
helped nobody. I could have added a dummy .OBJ that does nothing but
enforce the needed 2-byte alignment before the function if I
really insisted on keeping the C version, but it really wasn't
worth it.
Now that I've also described yet another meta-issue, maybe there'll
really be nothing to say about the next technical debt pushes?
Next up though: Back to actual progress
again, with TH01. Which maybe even ends up pushing that game over the 50%
RE mark?
With no feedback to 📝 last week's blog post,
I assume you all are fine with how things are going? Alright then, another
one towards position independence, with the same approach as before…
Since -Tom- wanted to learn something about how the PC-98
EGC is used in TH04 and TH05, I took a look at master.lib's
egc_shift_*() functions. These simply do a hardware-accelerated
memmove() of any VRAM region, and are used for screen shaking
effects. Hover over the image below for the raw effect:
Then, I finally wanted to take a look at the bullet structures, but it
required way too much reverse-engineering to even start within ¾ of
a position independence push. Even with the help of uth05win –
bullet handling was changed quite a bit from TH04 to TH05.
What I ultimately settled on was more raw, "boring" PI work based around
an already known set of functions. For this one, I looked at vector
construction… and this time, that actually made the games a little
bit more position-independent, and wasn't just all about removing
false positives from the calculation. This was one of the few sets of
functions that would also apply to TH01, and it revealed just how
chaotically that game was coded. This one commit shows three ways how ZUN
stored regular 2D points in TH01:
"regularly", like in master.lib's Point structure (X
first, Y second)
reversed, (Y first and X second), then obviously with two distinct
variables declared next to each other
… yeah. But in more productive news, this did actually lay the
groundwork for TH04 and TH05 bullet structures. Which might even be coming
up within the next big, 5-push order from Touhou Patch Center? These are
the priorities I got from them, let's see how close I can get!